Magnetic Claw Phone Mount – Clamps Bars up to 5 cm, 360° Rotation, No Tools
Magnetic Claw Phone Mount – Clamps Bars up to 5 cm, 360° Rotation, No Tools
Free shipping on every order
Take 10% off when you buy 2 or more
Details
Magnetic ring mount · Claw clamp · No tools
Clamp It On, Snap Your Phone On
No flat spot on the dashboard? No vent that holds a clip? This mount does not need either. Its claw grips a grab handle, seat post, tube or bar up to 5.1 cm (2 in), and the round magnetic head holds magnetic-ring phones and cases straight away. Other phones work too, with the included adhesive rings.
The usual problem
Where ordinary car holders fail
Magnetic strength
Strong hold, snap on and off
The round head has a magnet array made to the magnetic-ring standard used by most newer iPhones and many phone cases, so your phone snaps on and lines up by itself. The maker states it is stronger than the standard ring and in some cases can hold nearly 20 times the weight of a phone.
Phone or case without a magnet ring? Stick on one of the two included adhesive mounting rings and it holds just the same. Note: this mount holds the phone but does not charge it.
Secure grip
Grips handles, tubes and bars
The three-talon claw is tightened by hand with a built-in screw and keeps its position once tight. It grips tubes, grab handles, roll cages, square bars and flat rails from 0.6 to 5.1 cm (1/4 to 2 in), as long as the talons can reach opposite sides.
No tools are needed to fit it, and moving it to another vehicle is just as quick.
Viewing flexibility
Find the right angle
A twist-lock ball joint lets you turn the phone a full 360 degrees and tilt it to the angle you need, portrait or landscape. To go beyond the joint's range, loosen the claw slightly and reposition it.
Why this one
Magnetic claw mount vs the usual car phone holders
| This mount | Vent clip holder | Suction-cup holder | |
|---|---|---|---|
| Needs no flat dashboard spot | ✓ | ✓ | ✗ |
| Snap on and off with one hand | ✓ | some | some |
| Grips bars and handles up to 5.1 cm | ✓ | ✗ | ✗ |
| No sagging vent slats | ✓ | ✗ | ✓ |
| 360° rotation | ✓ | some | some |
| No tools to fit | ✓ | ✓ | ✓ |
How to use it
Ready in a minute
1. Clamp it on
Open the claw with the hand screw, place it around a handle, tube or bar and tighten by hand until it is firm.
2. Add a ring if needed
If your phone or case has no magnet ring, stick one of the included adhesive mounting rings on the back.
3. Snap and go
Set the angle with the ball joint and place your phone on the magnetic head.
Good to know
Before you buy
Questions people ask
Do I need to stick anything on my phone?
Not if your phone or case has a built-in magnetic ring, as most newer iPhones and many iPhone and Android cases do. Otherwise, use one of the two included adhesive mounting rings.
Do I need tools to fit the claw?
No. The claw is tightened by hand with one built-in screw and stays in position.
Can it clamp onto square tubes, flat rails or angled handles?
Usually yes, as long as the open talons can grasp opposite sides of the object.
What size bars does it fit?
From about 0.6 cm (1/4 in) up to 5.1 cm (2 in) thick.
Can I change the angle without loosening the claw?
Yes. The twist-lock ball joint gives full 360° rotation and tilt. To go beyond its range, loosen the claw slightly.
Can I use it on a motorcycle?
No. It is made for cars, trucks and other closed-cab vehicles.
Specifications
- Phone mounting: non-charging magnetic ring magnet array
- Mounting base: screw-driven three-talon claw, opens from 0.6 to 5.1 cm (0.25 to 2 in)
- Adjustment: twist-lock ball joint, 360° rotation and tilt
- Use: cars, trucks and closed-cab vehicles; not for motorcycles or open cabs
What's in the box
- 1 × magnetic claw phone mount
- 2 × adhesive mounting rings
- Instructions